What happens if you sand to bare steel and just use as insurance? – Rust Converter needs the rust to properly work and cure (think of it as the catalyst for the product). Rust Converter is intended for heavier rust. If applied over bare metal, it will not cure properly and can actually cause light flash rust.
Tag: how to
Rust Converter vs. Rust Encapsulator
Let’s face it, we all have rust issues to deal with. Some projects are better than others, but it’s hard to find a project car or truck that has no rust at all, even if it comes out of the Arizona desert. Eastwood makes many products for dealing with different […]
How to shave and metal finish your firewall with Empire Fabrication
Shaving or smoothing the bodywork on a custom car has been one of the most popular modifications since the beginning. Shaving door handles and trim or side marker holes are the most common things to shave on a project car, but close behind that is smoothing or shaving the firewall. Sean of Empire Fabrication has gotten REALLY good at shaving and smoothing cars. So much so that his finished projects require basically no body filler at all and can be primered and block sanded straight away. Sean recently took the time to snap some photos and give us the rundown on how he tackles a firewall shave project. The donor vehicle is a VW Eurovan that he has already drastically customized. So grab a drink, sit back, and watch how to do the job right with Empire Fabrication.
How to Flare Brake Lines (Live Stream Episode)
There are 3 basic types of flared ends you are likely to see on most cars: The single flare typically used on lower pressure fuel lines fittings, the double flare used on the high pressure brake lines of most vintage cars, and the bubble flare used on most modern and many older imported cars. In the picture the single flare is on the right, the double in the middle and the bubble on the left. With the proper Eastwood tools it is easy to make any of these flares.
Scratch building a Ford Hot Rod to Scale- Building a skeleton
Recently product developer Mark R. decided to build a 30’s Ford Hot Rod to scale. The process would be fun and it’s going to allow him to test a number of the new Eastwood Metal Fabrication tools and accessories we have coming down the pike. We figured we’d document the process and give you some sneak peaks at new products along the way.
Removing Rusty Floor Pans (Hands On Cars E.03)
Episode Summary: Using a rotisserie, an Eastwood MIG 175 welder, replacement stampings from National Part Depot and a BFH Kevin gets to work replacing the floorpans on the Zed Sled 1978 Chevy Camaro. After stripping the body shell inside and out, it’s apparent the floors are in much worse shape […]
How To Spray your first Wild Kustom Paintjob- Custom Lined, Candy and Flaked Skateboard Deck
Flake, Pearl, Candy, Lace, and all things flashy are what full blown Kustom Paintjobs are all about. If you want to flex your painting skills and standout with your paint job you’ll need to learn the process of custom taping, spaying candy, flake, and pearl. We decided to let Eastwood Tech Mike L. paint a skateboard to show you the basic steps to achieving a wild paint job like the pros do.
Hands On Cars Ep. 4 – Replacing a Rusty Roof
In this episode Kevin is all about undoing the errors of some previous owner of the Zed Sled Camaro Z28. He finishes up with the rust replacement on the bottom of the car, and tackles the cause of all the rot in the first place: A leaking aftermarket sunroof installation.
Beginners Metal Shaping Project- Making a panel blister.
Metal shaping is one of those things that seems like black magic to beginners. There really is a science behind the process that takes quite some time to learn and understand. The quickest and easiest way to understand how metal shaping works on the granular level is by comparing it to pizza dough. The more you stretch it out, the thinner it gets and the excess material has to go somewhere (in the pizza’s case its the rolled up crust) and the more you shrink the metal the thicker it gets and again it has to “go somewhere”. I decided to demonstrate a great beginner project for gaining experience in metal shaping by making a panel blister out of a 12″x12″x12″ piece of 5053 .035 aluminum. This process is great to help you understand the process and is pretty straight forward.