With more and more companies offering parts and supplies to upgrade your vehicle and get it trail-ready, we thought we’d put together our list of necessary items you should invest in when entering the Off-Road hobby. Some of these can be used at home and on the trail as well!
Tag: DIY
Tech Tip- How to Move a Bent Edge
On my Model A project I channeled the car down over the chassis which required me to build new floor supports and pans. The way I built it all up I needed to make 6 small pans that would fit down in between each supports. This meant I had to nail the bends on either edge so the final inside measurement allowed the pans to drop down in between the supports tightly. I will have to take the pans in and out throughout the rest of the project so I wanted them to drop in and fit snug, but not so tight I needed to use a hammer to force them in (this could also bow the panel).
The Sorcery of Tuck Shrinking Sheet Metal
The simplest way to describe how metal moves or reacts when you shrink or stretch it is to imagine pizza dough. When you stretch the dough out to make a larger pie you’ll see it gets larger AND thinner as you stretch it out. If you watch the process they start with a small, thick, round piece of dough that they kneed out until the dough is the desired thickness and put the excess material on the edges for the “crust” The same if they wanted to make the pie smaller, you’d need to gather the dough together creating bunches and smooth it all together until it was the desired shape. Metal reacts almost EXACTLY the same.
What is “Hot Flocking” and When do I do it?
This helps with adhesion, but can be VERY tricky if you aren’t careful. Start by cleaning your parts as good as possible, including any paint, grease or oil. I then like to run the part through the heat and cool cycle once heating the part past the curing temperature of your powder (check your powder bottle for the temperature). I then do one last wipe down with Acetone and then put it back in the oven and heat it to the curing temperature until the ENTIRE part is reading the cure temperature. Using an IR thermometer is key here.
Where and when do I use Epoxy Primer on my project?
In the past self etching primer was the go-to coating to apply over bare metal on a car. Metal required little prep work to apply it, it flashes/drys quickly, and it came in 1K Aerosol cans for small jobs. In the past 5-10 years you’ve probably been hearing more people talk about Epoxy Primers and their use as opposed to self etching primer. We decided to give you some insight on where and when epoxy primer works best.
How to fabricate and install Heavy Duty Threaded Inserts
Recently when channeling my Ford Model A I wanted to use Grade 8 fasteners for all of the body mounts instead of just tapping threads into the frame or inserting rivnuts that could fail over time. First of all the 1/4″ wall of the tubing wasn’t really thick enough to […]
How Much Paint Do You Need to Paint a Car?
There is no way to know exactly how much paint you need to paint every car, but there are basic guidelines. Of course the bigger the car, truck or van is the more paint you will need, and if you are spraying a basecoat/clearcoat you will need both components. One good way to make a more accurate estimate…
How to Make A Free Tuck Shrinking Fork
You may not realize it, but many of our Eastwood tools are dreamt up and prototyped the same way you build things at home. We have a problem or see a need for a tool to help do a job right and we build something ourselves. I recently needed to shrink the edge of a panel that was on a vehicle and I couldn’t get a shrinker stretcher on it to shrink. An alternative method is to “Tuck-Shrink” the area and use a hammer and dolly to shrink the metal into itself. I decided to make my own homemade tuck shrink tool from some old tools for free I had laying around and show you the process.
How to Keep Metal from Warping While Bead Rolling
If you have a bead roller, and you try to add a wide or deep bead to a thin piece of metal; or multiple beads to the same piece, you will find the metal starts to deform. You may get perfect beads in the piece you are working on, but it suddenly looks like a metal potato chip. That is because the bead roller does not necessarily stretch the metal as it presses beads into it. If you have an English wheel you can fix this problem before you begin. This problem is especially bad when rolling beads that don’t go all the way to the edge, or rolling different length beads in the same panel. Follow along as we show you a simple way to keep your panel straight when bead rolling.