Since guys have been customizing cars, shaving the door handles has been one of the most common modifications to make the car look as smooth as possible. This process can be a pretty simple process, but there are a few things that can make it go smoothly. I decided to show the process on Project Pile House.
Project Pile House
Ditch Those Leaky Header Joints
After you’ve been building and modifying cars for a while there’s some things that you become pretty particular about. It could be just how you like something to look or function, or just an extra step you take to save yourself headaches in the future. One of mine is an exhaust system that’s leak-free and sounds good. I’ve had bad luck over the years of header unions leaking over time. It seems either they crack at the welds or they just fit poorly and leave much to be desired when fitting the rest of the exhaust.
Custom Built Tailgate for Pile House
Possibly the biggest undertaking yet on this truck was making the new custom bed for Project Pilehouse. To quote Ron Covell in a metal shaping class at Eastwood headquarters; “I think those bedsides were the single largest pieces I’ve ever seen bead rolled in my life!”. The bed was definitely […]
Smoothing the Back End- Frenched Taillights on Pile House.
I will admit that I tend to over think things when I am building a custom car and sometimes I mock something up and I don’t like it or decide I need to tweak the original idea. A while back I decided on a set of ’62 Oldsmobile 88 taillights for the back of the truck. I liked the lens shape and chrome trim on them, but the bezel had peaked ends that made it tough to sink them into a relatively flat panel. For the sake of getting “something” in the rollpan I temporarily made brackets to slide them into the panel. At first I was “ok” with how they looked, but the further I got with building the tailgate on the backend I knew in the back of my head I needed to revisit how they were sitting.
Custom Scratch Built Bed DIY for Project Pile House
Project Pile House has been an ever-evolving project and like many projects, things start small and spiral out of control and next thing you know you’re detailing the inside of your glove box hinges! Luckily I’m not quite that OCD about my vehicles (yet), but Pile House is now more than just a thrown-together junkyard parts runner like I originally planned. It’s turned into a full blown custom and not much on the truck is original or untouched. After getting the cab, dash, hood, etc. all smoothed out and “roughed in”, the original patched together bed and fenders was bothering the crap out of me every time I looked at it. The fenders looked like boat trailer fenders and were more roughed up than a boxer after a title fight, while the bed itself wasn’t much better. I decided to start dreaming up a subtle custom bed.
Plumbing Custom Brake Lines on Project Pile House
First of all, if you’re rebuilding an old car, whether it’s a full blown 100 point restoration, or an out-of-this-world kustom, you shouldn’t forget about completely redoing the brakes on your ride. Brakes are one of the most overlooked part of a build that can save your car and your life. Project Pile House is a full blown custom with little to be left original on the truck. It sits on a first generation Chevy S10 chassis, so the brake components on each corner are easy to get replacements for, but that’s about where it stops being easy. I recently decided to plumb the brake system on Pile House, and show you what goes into a project like this.
Project Pile House Shaving and customizing the original dash and glovebox.
While I had the column out I decided to start cleaning up the dash and sort out my brake pedal dilemma on the truck. In order to get under the dash for fabricating the new brake pedal setup and to shave and smooth the dash I needed to pull it out. ….
Shaving the Column- Custom Steering Column Mods
I had previously covered in a few steps how I had come up with the steering setup on the truck. To make it short, I’m using a Packard steering column housing, a custom column shaft, and a Ford steering wheel. To make all of this work together took a bit of work, but I’ve got it all bolted up and it should all jive pretty good when done. Now I need to finish up the small details that will make the column not only look good, but also work smoothly together. I’ll be covering the latter in another post, but for now I decided to show you how I went about shaving the unneeded holes from the column housing.
Custom Hood Modifications- Converting a Multi-Piece Hood to One Piece
One thing that I’ve planned to customize on Project Pile House from day one was the hood. The hood on the truck is a “butterfly” (as I call it) style hood and was a design that Dodge rolled over from 30’s and 40’s trucks. I have taken a 50’s custom type approach to this truck and that style hood wasn’t going to flow. I decided to disassemble the hood and convert it to a one-piece hood.